< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=1397796048310106&ev=PageView&noscript=1" /> logo
blog
BLOG DETAILS
Home > Blog >
Sausage Filling Machine for Canada: 208/480/600 V, CSA and a Real Capacity Checklist
Events
Contact Us
Mr. Tom Lau
86--18753190140
wechat +86 18753190140
Contact Now

Sausage Filling Machine for Canada: 208/480/600 V, CSA and a Real Capacity Checklist

2026-11-20
Latest company blogs about Sausage Filling Machine for Canada: 208/480/600 V, CSA and a Real Capacity Checklist

A sausage filler is one of the few machines in a meat plant where the electrical spec can cost more than the machine. We have shipped vacuum fillers into Ontario and Alberta where the plant had 600 V three-phase service and a 380 V / 50 Hz motor on the nameplate, and the first conversation on site was not about casings or portion weight — it was about a replacement motor, a buck-boost transformer and a field evaluation sticker.

This guide is written from our commissioning reports for Canadian plants, not from a catalogue. The machine figures below are from the units we build: the 220 L vacuum filler (ZKG3500 / ZKG6500), the 240 L servo-driven vacuum filler (EPS-3200T) and the 60 L / 80 L vertical hydraulic stuffers. The electrical and regulatory notes are the ones that actually stop a shipment at the dock.

1. Start at the panel: what Canada will actually give you

Canada is a 60 Hz country with four supply arrangements you will meet in food plants. Ask the customer for a photo of the panel schedule and the breaker size before quoting anything.

SupplyWhere you meet itWhat it means for a filler
120/240 V, 1 ph, 60 HzSmall butcher shops, farm-gate processorsOnly small 60 L hydraulic or pneumatic units; 1.5–2.2 kW is the practical ceiling
208Y/120 V, 3 ph, 60 HzOlder commercial buildings, retail commissariesMost common surprise: a “208 V" service, not 240 V. Motors must be dual-rated or VFD-driven
480Y/277 V, 3 ph, 60 HzMost modern food plantsStandard industrial choice; 460 V motors, 480 V controls
600 V, 3 ph, 60 HzQuebec and older large plants, some mines and remote sites575 V motors on a 600 V system; separate starter and overload range

Our standard export build is 380 V / 50 Hz. That is not a Canadian machine. A 50 Hz motor run on 60 Hz turns 20% faster, so a 1,440 rpm four-pole motor becomes 1,740 rpm, the vacuum pump runs beyond its designed displacement, and the servo/portioning timing drifts. There are only three honest ways to fix it:

  • Order a 60 Hz motor at the factory. Cleanest option. Same frame, 60 Hz winding, nameplate 208–230/460 V or 575 V.
  • Use a VFD and lock the base frequency to 60 Hz. Then set the maximum output frequency to 50 Hz if you want to keep the original mechanical speed. Do not let the drive “helpfully" run to 60 Hz.
  • Re-rate the motor. A 50 Hz motor on 60 Hz keeps its torque but loses about 15–20% of its service factor margin; on a 7 kW vacuum filler that is the difference between a 3,500 kg/h day and a hot motor by 14:00.

Current matters more than kilowatts when the electrician is standing next to you. For the 7 kW ZKG3500 at a realistic 0.85 power factor and 0.88 efficiency:

Site voltageFull-load currentSuggested breakerNotes
208 V, 3 ph≈ 26 A30 ACheck voltage drop on long runs; 208 V plants often have 180–195 V at the far panel
480 V, 3 ph≈ 11.3 A15 AStandard North American starter, 460 V coil
600 V, 3 ph≈ 9 A15 A575 V motor, 600 V rated disconnect

Three details that fail inspection in Canada and are cheap to get right at build stage: a lockable disconnect within sight of the operator; a control panel built to CSA C22.2 No. 14 with cUL or CSA marked components; and TECK90 or armoured cable for the drop, not flexible cord. If the panel is built in China without a CSA/UL mark, the customer will need a field evaluation to CSA SPE-1000 before the local inspector will energise it — budget CAD 1,500–4,000 and a week of site time for that, and tell the buyer before they buy, not after.

2. What CFIA asks of the machine itself

Canada does not certify sausage fillers. It certifies the establishment. Under the Safe Food for Canadians Regulations (SFCR, in force since 15 January 2019), a federally licensed meat establishment must run written preventive controls covering sanitation, equipment maintenance, employee competency and process control. The inspector then looks at your filler and asks a simple question: can you clean it, and can you prove it?

In practice that means the buyer's maintenance log will be checked against these design points:

  • SUS304 contact surfaces, welds ground flush and passivated; no lap joints, no exposed screw threads in the product path.
  • Surface roughness Ra ≤ 0.8 µm on the hopper, cylinder and filling head. We check with a portable profilometer on three points per part and record the values in the test sheet.
  • Tool-free strip-down of the filling head, valve and casing horn in under 10 minutes. If a cleaner needs a spanner, it will not be stripped every shift.
  • Sloped, self-draining surfaces; no horizontal ledges wider than 6 mm; feet sealed to the floor or on castors that clear a 100 mm washdown gap.
  • Non-metallic parts (seals, gaskets, suction hoses) with a food-contact declaration. EPDM and silicone are fine; natural rubber is not.

Two Canadian-specific points that are usually missed. First, federally registered establishments trade interprovincially and internationally; a provincially licensed plant selling only inside its province is inspected against provincial meat hygiene rules instead, which are broadly similar but not identical. Ask which licence the customer holds, because it changes how much documentation they need from you. Second, if the customer packs retail sausage, the label must be bilingual English and French under the Food and Drug Regulations (B.01.012) and the Consumer Packaging and Labelling Act. Your machine does not print the label, but the customer will ask you to hold portion weight within ±1.5 g/100 g so the declared net weight survives audit — which is exactly what the vacuum filler's portioning accuracy is for.

3. Capacity: kg/h on paper versus kg/h on a Tuesday

Nameplate capacity is measured with a clean cylinder, warm farce and one operator doing nothing else. Real output is 65–80% of that. Our models, with real numbers:

ModelHopper / cylinderPowerRated outputRealistic shift output
Single-tube vertical hydraulic60 L / 30 L1.5 kW300–400 kg/h220–300 kg/h
Double-tube vertical hydraulic80 L / 40 L2.2 kW600–800 kg/h450–620 kg/h
EPS-3200T vacuum, servo240 L4.75 kW3,000 kg/h2,100–2,400 kg/h
ZKG3500 vacuum220 L7 kW3,500 kg/h2,500–2,900 kg/h
ZKG6500 vacuum220 L8 kW4,500 kg/h3,200–3,700 kg/h

Do the arithmetic on casings, not on kilograms. A 34–36 mm hog casing holds roughly 0.9–1.1 kg per metre; a 22 mm sheep casing for breakfast links holds about 0.35 kg/m. A plant making 5,000 kg/week of 34 mm sausage in two 6-hour stuffing days needs 417 kg/h, and the double-tube 80 L unit will do it with one buffer trolley. The same plant at 20,000 kg/week needs 1,670 kg/h and should be on a 220 L vacuum filler, because the labour to keep a small hopper fed costs more than the machine difference within a year.

Vacuum is not a luxury in a Canadian plant. Air pockets in a 36 mm casing show up as grey rings after cooking, and the retail buyer rejects the lot. Our ZKG-series pulls 24 m³/h through a 0.8–0.9 bar vacuum and holds density consistently; the servo-driven EPS-3200T adds ±1.5 g/100 g portioning on mild farce and ±2 g/100 g on coarse/block product, which is what makes weight-declared retail packs feasible.

4. The Canadian product mix changes the setup

Canada is not one market. The casing schedule and the farce temperature change by region, and the machine has to be specified for the mix the customer actually runs:

  • Ontario: peameal bacon dominates the tourist counter, but it is a brined loin, not a stuffed product. The filler work is breakfast links (19–22 mm sheep), bratwurst and fresh garlic sausage (32–36 mm hog).
  • Quebec: maple breakfast sausage, tourtière-adjacent coarse pork blends, and a strong charcuterie culture. Farce is coarse, 6–8 mm plate, and sticky — use the low-speed/high-pressure setting, not the high-speed setting.
  • Prairies: kubasa / kielbasa in 38–42 mm hog or collagen, often smoked. Lean game blends (bison, elk) need 20–25% added pork fat or the stuffer will stall and smear.
  • Atlantic: seafood sausage and chowder bases. Salt content is high; specify 316L for the cylinder and horn if brine exceeds 3%.
  • Halal lines in the GTA and Montreal: beef and chicken, separate casing inventory, and a documented allergen/ species changeover between runs.

Two operating numbers to write into the SOP. Keep farce at 0–2 °C at the stuffer; above 6 °C the fat smears and you lose the bite. And pre-soak natural casings in 0–4 °C water for at least 24 hours, changing the water twice — frozen casings straight from the freezer are the single most common cause of blowouts we get called about in January.

5. Cold climate, condensation and washdown

A machine that works in Guangzhou can fail in Saskatoon for reasons that have nothing to do with the motor. At −30 °C outside, the plant is a humidity pump: warm, wet air from the cook room hits a cold machine body and condenses inside the panel. Our cold-climate build adds a thermostatted anti-condensation heater in the control cabinet, IP65 seals on the door, and a drip shield over the terminal box. If the machine sits idle overnight in an unheated room, specify ISO VG32 hydraulic oil instead of VG46, and a 30-minute low-pressure warm-up cycle before production.

Washdown is the other half. Canadian plants typically clean at 55–60 °C with alkaline detergent and sanitise at 82 °C or with a quat. The filler should be IP65 minimum at the panel, IP69K at the head, with a drain plug in the hopper and no water traps behind the cylinder. Check the floor: a 1:100 slope to a trapped drain is an inspection item, and a machine levelled with shims that create a puddle is an inspection finding.

6. Acceptance checklist before the final payment

Run this on site, at the customer's real voltage, with the customer's own farce. We put the same list in the commissioning report and both sides sign it.

  1. Two hours at full load; record phase current on all three phases. Imbalance ≤ 2%.
  2. Voltage at the panel under load; if it falls below 95% of nominal, stop and fix the supply, not the machine.
  3. Thirty consecutive portions weighed individually; all within the agreed tolerance (±1.5 g/100 g mild, ±2 g/100 g coarse).
  4. Vacuum leak-down: isolate the pump, ≤ 5 mbar rise per minute.
  5. Casing test on the largest and smallest casing in the customer's schedule; no blowout at the rated fill pressure.
  6. Guard interlock: filling stops within 1 second of the guard opening.
  7. Noise ≤ 80 dB(A) at the operator position, measured at 1 m.
  8. Insulation resistance ≥ 1 MΩ; earth continuity ≤ 0.1 Ω.
  9. Strip-down time, timed with a stopwatch, ≤ 10 minutes by the customer's own cleaner.
  10. Cleanliness verification after washdown: ATP swab at five points, < 150 RLU each.

7. Buying, shipping and the paperwork

First orders in Canada are usually T/T 30% deposit and 70% before shipment; L/C at sight appears above roughly USD 100,000 or with a new importer using a bank facility. FOB Qingdao or Ningbo is the norm, with CIF Vancouver or Prince Rupert for west-coast buyers and CIF Montreal or Halifax for the east. Transit is about 14–18 days to Vancouver, 12–16 to Prince Rupert, and 30–35 to Montreal; add 7–10 days by rail to Toronto. If the buyer wants DDP, price the GST/HST and the customs brokerage separately — GST/HST is recoverable for a registered business, but it is still cash out at the border.

Classify under HS 8438.50 (machinery for the preparation of meat) and confirm the current MFN rate with the buyer's broker; most food-processing machinery enters Canada at 0% MFN, but the ruling belongs to the importer, not to us. Ship with a spare kit: two sets of seals, one filling horn per casing size, a suction hose, a set of contactors and an overload relay matched to the site voltage. A CAD 400 seal kit air-freighted in February costs less than three days of downtime.

Shandong EPS Machinery has been building food machinery for 15 years and ships to more than 50 countries. Every unit is assembled and run under load before packing, and the test sheet — including the motor nameplate voltage, the vacuum leak-down figure and the portion weights — travels with the machine. If you are specifying for a Canadian plant, send us the panel schedule and the product list first; we will answer with a voltage-specific quotation and a casing schedule, not a generic brochure.

FAQ

Can you supply a 600 V machine directly? Yes. Specify 575 V / 60 Hz motors and a 600 V rated disconnect at order. Retrofitting a 380 V / 50 Hz unit on site is possible with a transformer and a motor change, but it costs more than ordering correctly.

Do we need CSA certification on the machine? The machine needs CSA/UL marked components and a panel to CSA C22.2 No. 14. If it arrives unlisted, the local authority requires a field evaluation to CSA SPE-1000 before connection. We can build to that standard and provide the component list in advance.

Is a 208 V service a problem for a 7 kW filler? Not if it is specified as 208 V. The current rises to about 26 A, so use a 30 A breaker and 10 mm² conductors. The failure mode is ordering a 380 V machine and discovering 208 V on site.

How much does cold-climate build add? Typically 3–5% on the machine price for the cabinet heater, IP65 upgrade, cold-oil specification and drip shielding. It is far cheaper than a February panel failure.

blog
BLOG DETAILS
Sausage Filling Machine for Canada: 208/480/600 V, CSA and a Real Capacity Checklist
2026-11-20
Latest company news about Sausage Filling Machine for Canada: 208/480/600 V, CSA and a Real Capacity Checklist

A sausage filler is one of the few machines in a meat plant where the electrical spec can cost more than the machine. We have shipped vacuum fillers into Ontario and Alberta where the plant had 600 V three-phase service and a 380 V / 50 Hz motor on the nameplate, and the first conversation on site was not about casings or portion weight — it was about a replacement motor, a buck-boost transformer and a field evaluation sticker.

This guide is written from our commissioning reports for Canadian plants, not from a catalogue. The machine figures below are from the units we build: the 220 L vacuum filler (ZKG3500 / ZKG6500), the 240 L servo-driven vacuum filler (EPS-3200T) and the 60 L / 80 L vertical hydraulic stuffers. The electrical and regulatory notes are the ones that actually stop a shipment at the dock.

1. Start at the panel: what Canada will actually give you

Canada is a 60 Hz country with four supply arrangements you will meet in food plants. Ask the customer for a photo of the panel schedule and the breaker size before quoting anything.

SupplyWhere you meet itWhat it means for a filler
120/240 V, 1 ph, 60 HzSmall butcher shops, farm-gate processorsOnly small 60 L hydraulic or pneumatic units; 1.5–2.2 kW is the practical ceiling
208Y/120 V, 3 ph, 60 HzOlder commercial buildings, retail commissariesMost common surprise: a “208 V" service, not 240 V. Motors must be dual-rated or VFD-driven
480Y/277 V, 3 ph, 60 HzMost modern food plantsStandard industrial choice; 460 V motors, 480 V controls
600 V, 3 ph, 60 HzQuebec and older large plants, some mines and remote sites575 V motors on a 600 V system; separate starter and overload range

Our standard export build is 380 V / 50 Hz. That is not a Canadian machine. A 50 Hz motor run on 60 Hz turns 20% faster, so a 1,440 rpm four-pole motor becomes 1,740 rpm, the vacuum pump runs beyond its designed displacement, and the servo/portioning timing drifts. There are only three honest ways to fix it:

  • Order a 60 Hz motor at the factory. Cleanest option. Same frame, 60 Hz winding, nameplate 208–230/460 V or 575 V.
  • Use a VFD and lock the base frequency to 60 Hz. Then set the maximum output frequency to 50 Hz if you want to keep the original mechanical speed. Do not let the drive “helpfully" run to 60 Hz.
  • Re-rate the motor. A 50 Hz motor on 60 Hz keeps its torque but loses about 15–20% of its service factor margin; on a 7 kW vacuum filler that is the difference between a 3,500 kg/h day and a hot motor by 14:00.

Current matters more than kilowatts when the electrician is standing next to you. For the 7 kW ZKG3500 at a realistic 0.85 power factor and 0.88 efficiency:

Site voltageFull-load currentSuggested breakerNotes
208 V, 3 ph≈ 26 A30 ACheck voltage drop on long runs; 208 V plants often have 180–195 V at the far panel
480 V, 3 ph≈ 11.3 A15 AStandard North American starter, 460 V coil
600 V, 3 ph≈ 9 A15 A575 V motor, 600 V rated disconnect

Three details that fail inspection in Canada and are cheap to get right at build stage: a lockable disconnect within sight of the operator; a control panel built to CSA C22.2 No. 14 with cUL or CSA marked components; and TECK90 or armoured cable for the drop, not flexible cord. If the panel is built in China without a CSA/UL mark, the customer will need a field evaluation to CSA SPE-1000 before the local inspector will energise it — budget CAD 1,500–4,000 and a week of site time for that, and tell the buyer before they buy, not after.

2. What CFIA asks of the machine itself

Canada does not certify sausage fillers. It certifies the establishment. Under the Safe Food for Canadians Regulations (SFCR, in force since 15 January 2019), a federally licensed meat establishment must run written preventive controls covering sanitation, equipment maintenance, employee competency and process control. The inspector then looks at your filler and asks a simple question: can you clean it, and can you prove it?

In practice that means the buyer's maintenance log will be checked against these design points:

  • SUS304 contact surfaces, welds ground flush and passivated; no lap joints, no exposed screw threads in the product path.
  • Surface roughness Ra ≤ 0.8 µm on the hopper, cylinder and filling head. We check with a portable profilometer on three points per part and record the values in the test sheet.
  • Tool-free strip-down of the filling head, valve and casing horn in under 10 minutes. If a cleaner needs a spanner, it will not be stripped every shift.
  • Sloped, self-draining surfaces; no horizontal ledges wider than 6 mm; feet sealed to the floor or on castors that clear a 100 mm washdown gap.
  • Non-metallic parts (seals, gaskets, suction hoses) with a food-contact declaration. EPDM and silicone are fine; natural rubber is not.

Two Canadian-specific points that are usually missed. First, federally registered establishments trade interprovincially and internationally; a provincially licensed plant selling only inside its province is inspected against provincial meat hygiene rules instead, which are broadly similar but not identical. Ask which licence the customer holds, because it changes how much documentation they need from you. Second, if the customer packs retail sausage, the label must be bilingual English and French under the Food and Drug Regulations (B.01.012) and the Consumer Packaging and Labelling Act. Your machine does not print the label, but the customer will ask you to hold portion weight within ±1.5 g/100 g so the declared net weight survives audit — which is exactly what the vacuum filler's portioning accuracy is for.

3. Capacity: kg/h on paper versus kg/h on a Tuesday

Nameplate capacity is measured with a clean cylinder, warm farce and one operator doing nothing else. Real output is 65–80% of that. Our models, with real numbers:

ModelHopper / cylinderPowerRated outputRealistic shift output
Single-tube vertical hydraulic60 L / 30 L1.5 kW300–400 kg/h220–300 kg/h
Double-tube vertical hydraulic80 L / 40 L2.2 kW600–800 kg/h450–620 kg/h
EPS-3200T vacuum, servo240 L4.75 kW3,000 kg/h2,100–2,400 kg/h
ZKG3500 vacuum220 L7 kW3,500 kg/h2,500–2,900 kg/h
ZKG6500 vacuum220 L8 kW4,500 kg/h3,200–3,700 kg/h

Do the arithmetic on casings, not on kilograms. A 34–36 mm hog casing holds roughly 0.9–1.1 kg per metre; a 22 mm sheep casing for breakfast links holds about 0.35 kg/m. A plant making 5,000 kg/week of 34 mm sausage in two 6-hour stuffing days needs 417 kg/h, and the double-tube 80 L unit will do it with one buffer trolley. The same plant at 20,000 kg/week needs 1,670 kg/h and should be on a 220 L vacuum filler, because the labour to keep a small hopper fed costs more than the machine difference within a year.

Vacuum is not a luxury in a Canadian plant. Air pockets in a 36 mm casing show up as grey rings after cooking, and the retail buyer rejects the lot. Our ZKG-series pulls 24 m³/h through a 0.8–0.9 bar vacuum and holds density consistently; the servo-driven EPS-3200T adds ±1.5 g/100 g portioning on mild farce and ±2 g/100 g on coarse/block product, which is what makes weight-declared retail packs feasible.

4. The Canadian product mix changes the setup

Canada is not one market. The casing schedule and the farce temperature change by region, and the machine has to be specified for the mix the customer actually runs:

  • Ontario: peameal bacon dominates the tourist counter, but it is a brined loin, not a stuffed product. The filler work is breakfast links (19–22 mm sheep), bratwurst and fresh garlic sausage (32–36 mm hog).
  • Quebec: maple breakfast sausage, tourtière-adjacent coarse pork blends, and a strong charcuterie culture. Farce is coarse, 6–8 mm plate, and sticky — use the low-speed/high-pressure setting, not the high-speed setting.
  • Prairies: kubasa / kielbasa in 38–42 mm hog or collagen, often smoked. Lean game blends (bison, elk) need 20–25% added pork fat or the stuffer will stall and smear.
  • Atlantic: seafood sausage and chowder bases. Salt content is high; specify 316L for the cylinder and horn if brine exceeds 3%.
  • Halal lines in the GTA and Montreal: beef and chicken, separate casing inventory, and a documented allergen/ species changeover between runs.

Two operating numbers to write into the SOP. Keep farce at 0–2 °C at the stuffer; above 6 °C the fat smears and you lose the bite. And pre-soak natural casings in 0–4 °C water for at least 24 hours, changing the water twice — frozen casings straight from the freezer are the single most common cause of blowouts we get called about in January.

5. Cold climate, condensation and washdown

A machine that works in Guangzhou can fail in Saskatoon for reasons that have nothing to do with the motor. At −30 °C outside, the plant is a humidity pump: warm, wet air from the cook room hits a cold machine body and condenses inside the panel. Our cold-climate build adds a thermostatted anti-condensation heater in the control cabinet, IP65 seals on the door, and a drip shield over the terminal box. If the machine sits idle overnight in an unheated room, specify ISO VG32 hydraulic oil instead of VG46, and a 30-minute low-pressure warm-up cycle before production.

Washdown is the other half. Canadian plants typically clean at 55–60 °C with alkaline detergent and sanitise at 82 °C or with a quat. The filler should be IP65 minimum at the panel, IP69K at the head, with a drain plug in the hopper and no water traps behind the cylinder. Check the floor: a 1:100 slope to a trapped drain is an inspection item, and a machine levelled with shims that create a puddle is an inspection finding.

6. Acceptance checklist before the final payment

Run this on site, at the customer's real voltage, with the customer's own farce. We put the same list in the commissioning report and both sides sign it.

  1. Two hours at full load; record phase current on all three phases. Imbalance ≤ 2%.
  2. Voltage at the panel under load; if it falls below 95% of nominal, stop and fix the supply, not the machine.
  3. Thirty consecutive portions weighed individually; all within the agreed tolerance (±1.5 g/100 g mild, ±2 g/100 g coarse).
  4. Vacuum leak-down: isolate the pump, ≤ 5 mbar rise per minute.
  5. Casing test on the largest and smallest casing in the customer's schedule; no blowout at the rated fill pressure.
  6. Guard interlock: filling stops within 1 second of the guard opening.
  7. Noise ≤ 80 dB(A) at the operator position, measured at 1 m.
  8. Insulation resistance ≥ 1 MΩ; earth continuity ≤ 0.1 Ω.
  9. Strip-down time, timed with a stopwatch, ≤ 10 minutes by the customer's own cleaner.
  10. Cleanliness verification after washdown: ATP swab at five points, < 150 RLU each.

7. Buying, shipping and the paperwork

First orders in Canada are usually T/T 30% deposit and 70% before shipment; L/C at sight appears above roughly USD 100,000 or with a new importer using a bank facility. FOB Qingdao or Ningbo is the norm, with CIF Vancouver or Prince Rupert for west-coast buyers and CIF Montreal or Halifax for the east. Transit is about 14–18 days to Vancouver, 12–16 to Prince Rupert, and 30–35 to Montreal; add 7–10 days by rail to Toronto. If the buyer wants DDP, price the GST/HST and the customs brokerage separately — GST/HST is recoverable for a registered business, but it is still cash out at the border.

Classify under HS 8438.50 (machinery for the preparation of meat) and confirm the current MFN rate with the buyer's broker; most food-processing machinery enters Canada at 0% MFN, but the ruling belongs to the importer, not to us. Ship with a spare kit: two sets of seals, one filling horn per casing size, a suction hose, a set of contactors and an overload relay matched to the site voltage. A CAD 400 seal kit air-freighted in February costs less than three days of downtime.

Shandong EPS Machinery has been building food machinery for 15 years and ships to more than 50 countries. Every unit is assembled and run under load before packing, and the test sheet — including the motor nameplate voltage, the vacuum leak-down figure and the portion weights — travels with the machine. If you are specifying for a Canadian plant, send us the panel schedule and the product list first; we will answer with a voltage-specific quotation and a casing schedule, not a generic brochure.

FAQ

Can you supply a 600 V machine directly? Yes. Specify 575 V / 60 Hz motors and a 600 V rated disconnect at order. Retrofitting a 380 V / 50 Hz unit on site is possible with a transformer and a motor change, but it costs more than ordering correctly.

Do we need CSA certification on the machine? The machine needs CSA/UL marked components and a panel to CSA C22.2 No. 14. If it arrives unlisted, the local authority requires a field evaluation to CSA SPE-1000 before connection. We can build to that standard and provide the component list in advance.

Is a 208 V service a problem for a 7 kW filler? Not if it is specified as 208 V. The current rises to about 26 A, so use a 30 A breaker and 10 mm² conductors. The failure mode is ordering a 380 V machine and discovering 208 V on site.

How much does cold-climate build add? Typically 3–5% on the machine price for the cabinet heater, IP65 upgrade, cold-oil specification and drip shielding. It is far cheaper than a February panel failure.

sitemap |  Privacy Policy | China Good Quality Meat Cutting Machine Supplier. Copyright © 2025-2026 SHANDONG EPS MACHINERY CO.,LTD . All Rights Reserved.